KOOL SEAL INC -- UNIFLEX ACRYLIC WHITE PATCHING COMPOUND, 41-220  -- 5610-00N057183
<pre>=====================  Product Identification  =====================

Product ID:UNIFLEX ACRYLIC WHITE PATCHING COMPOUND, 41-220
MSDS Date:11/08/1991
FSC:5610
NIIN:00N057183
=== Responsible Party ===
Company Name:KOOL SEAL INC
Address:1499 ENTERPRISE PKWY
City:TWINSBURG
State:OH
ZIP:44087
Country:US
Info Phone Num:216-425-4717
Emergency Phone Num:216-951-6969
CAGE:23820
=== Contractor Identification ===
Company Name:KOOL SEAL INC
Address:1499 ENTERPRISE PARKWAY
Box:City:TWINSBURG
State:OH
ZIP:44087
Country:US
Phone:216-425-4717
CAGE:23820

=============  Composition/Information on Ingredients  =============

Ingred Name:AMMONIA (SARA 302/313) (CERCLA) VP:765 @ 80F
CAS:7664-41-7
RTECS #:BO0875000
Fraction by Wt: 0.03%
OSHA PEL:50 PPM
ACGIH TLV:25 PPM
EPA Rpt Qty:100 LBS
DOT Rpt Qty:100 LBS

Ingred Name:VOLATILE ORGANIC COMPOUND:41 GR/L
RTECS #:9999999VO
OSHA PEL:N/K 
ACGIH TLV:N/K 

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:NO
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:EFFECTS OF OVEREXPOSURE:SKIN:PROLONGED
    OR REPEATED CONTACT MAY CAUSE SLIGHT IRRITATION TO SENSITIVE SKIN.
    EYES:CONTACT MAY CAUSE IRRITATION. INHALATION:VAPOR MAY AGGRAVATE
    SENSITIVE TISSUE IN NASAL AN D RESPIRATORY PASSAGES.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:VAPOR MAY AGGRAVATE SENSITIVE
    TISSUE IN NASAL AND RESPIRATORY PASSAGES.

=======================  First Aid Measures  =======================

First Aid:INHAL:REMOVE TO FRESH AIR. SUPPORT BREATHING (GIVE O*2/ARTF
    RESP) . SKIN:WASH WITH SOAP AND WATER. EYES:FLUSH WITH LARGE
    AMOUNTS OF WATER FOR AT LEAST 15 MINUTES. SEE PHYSICIAN.
    INGESTION:GIVE 2  GLASSES OF WATER TO DILUTE. DO NOT INDUCE
    VOMITING. CONSULT PHYSICIAN. TREAT SYMPTOMATICALLY.

=====================  Fire Fighting Measures  =====================

Flash Point:NONE
Extinguishing Media:FOAM, ALCOHOL FOAM, CO*2, DRY CHEMICAL, WATER FOG.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
    PROTECTIVE EQUIPMENT . IF WATER IS USED, FOG NOZZLES ARE
    PREFERABLE.
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE WHEN
    EXPOSED TO EXTREME HEAT. WATER MAY BE USED TO COOL UNRUPTURED
    CONTAINERS.

==================  Accidental Release Measures  ==================

Spill Release Procedures:CONTAIN SPILL WITH INERT MATERIAL, (SAND,
    EARTH, ETC.,) AND TRANFER TO CONTAINER FOR PROPER DISPOSAL. FLOORS
    MAY BE SLIPPERY. CARE SHOULD BE EXERCISED TO AVOID FALLS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:KEEP FROM FREEZING.
Other Precautions:KEEP CLOSURE TIGHT AND CONTAINER UPRIGHT TO PREVENT
    LEAKAGE. KEEP OUT OF REACH OF CHILDREN.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:USE NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE
    FOR EXPOSURE OF CONCERN . NONE REQUIRED.
Ventilation:GENERAL ROOM VENTILATION SHOULD BE PROVIDED TO KEEP AIR
    CONTAINMENT BELOW OSHA PERMISSIBLE EXPOSURE LIMIT.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPROVED SAFETY GLASSES .
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:WASH CONTAIMINATED CLOTHING BEFORE REUSE.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

==================  Physical/Chemical Properties  ==================

Boiling Pt:B.P. Text:212F,100C
Vapor Pres:SEE INGS
Vapor Density:HVR/AIR
Spec Gravity:1.37 
Evaporation Rate &amp; Reference:SLOWER THAN ETHER
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
NOT APPLICABLE.
Stability Condition to Avoid:NONE
Hazardous Decomposition Products:MAY PRDCE FUMES WHEN DRIED FILM IS
    HEATED TO DECOMP, AS IN WELDING. FUMES MAY CONTAIN CARBON MONOXIDE
    & CARBON DIOXIDE.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE OF SPILLED MATERIAL IN ACCORDANCE WITH
    FEDERAL, STATE AND LOCAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.